BACnet Fire 3rd Party Commands

The following describes the commands available for the BACnet Fire 3rd Party integration.

Commands on Analog Input Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command
Units	Change
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Out of Service	Out of Svc In Service
Reliability	Change
High Limit	Change
Low Limit	Change
Limit Enable	Change
COV Increment	Change
Deadband	Change
Max Present Value	Change
Min Present Value	Change
Update Interval	Change

Commands on Analog Output Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command Release
Units	Change
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Priority Array	Command Release
Out of Service	Out of Svc In Service
Reliability	Change
High Limit	Change
Low Limit	Change
Limit Enable	Change
COV Increment	Change
Deadband	Change
Max Present Value	Change
Min Present Value	Change
Relinquish Default	Change

Commands on Analog Value Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command Release
Units	Change
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Priority Array	Command Release
Out of Service	Out of Svc In Service
Reliability	Change
High Limit	Change
Low Limit	Change
Limit Enable	Change
COV Increment	Change
Min Present Value	Change
Max Present Value	Change
Deadband	Change
Relinquish Default	Change
Time Delay	Change

Commands on Binary Input Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Out of Service	Out of Svc In Service
Reliability	Change
Polarity	Normal Reversed
Profile Name	Change

Commands on Binary Output Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command Release
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Out of Service	Out of Svc In Service
Priority Array	Command Release
Feedback Value	Change
Reliability	Change
Minimum Off Time	Change
Minimum On Time	Change
Polarity	Normal Reversed
Relinquish Default	Change

Commands on Binary Value Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command Release
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Out of Service	Out of Svc In Service
Priority Array	Command Release
Reliability	Change
Minimum Off Time	Change
Minimum On Time	Change
Relinquish Default	Change

Commands on Device Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Local Time	Time Sync
Location	Change
Firmware Revision	Rediscover

Commands on Life Safety Point Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Mode	Send
Acknowledged Transitions	Ack
Reliability	Change
Operation Expected	Reset
Silenced	Silence
Event Detection Enable	Enable Disable
Units	Change

Commands on Life Safety Zone Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Mode	Send
Acknowledged Transitions	Ack
Reliability	Change
Operation Expected	Reset
Silenced	Silence
Event Detection Enable	Enable Disable

Commands on Multi State Input Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command
Acknowledged Transitions	Ack Reset
Out of Service	Out of Svc In Service
Reliability	Change

Commands on Multi State Output Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command Release
Acknowledged Transitions	Ack All Ack OffNormal Ack Fault Ack Normal
Out of Service	Out of Svc In Service
Reliability	Change
Relinquish Default	Command
Reliability Evaluation Inhibit False	Enable Disable

Commands on Multi State Value Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All
Present Value	Command Release
Acknowledged Transitions	Ack Reset
Out of Service	Out of Svc In Service

Commands on Notification Class Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All

Commands on Structured View Objects
Property	Commands
Alarm Suppression	Enable Disable Enable All Disable All

Extend or Reduce the Commands on the Mode Property

Do one of the following:

If you want to add and remove commands:
a. Save the TxG_BACnetFire_ModeCmd text group as a new one.
b. Modify the new text group as necessary.
c. Assign the new text group to the customized object model or instance if needed.

If you only want to add new commands:
- Modify the TxG_BACnetFire_ModeCmd text group as necessary.
No other changes are required to the object model or instance since the customized text group is automatically assigned to all instances of that specific object model.

When new commands are added they must take the identifier from the text group TxG_BACnetFire_LifeSafetyMode while the text must reflect the corresponding command (for example, 5 Slow or 8 Fast).